In short

  • Auto Bild tested 10 torque wrenches (1 August 2026) in the accredited calibration lab of Gedore. Winners: Hazet 5122-3CT (1.4, €129.03) and Gedore TORCOFIX TF-K200 (1.4, €151.95).
  • The cheapest, a TECPO set with sockets at €24.29, scored 3.9 with only sufficient precision. The €67 BGS 7183 got 3.7.
  • Wheel bolts are a safety item. A wrench that is 4 percent off at 120 Nm is about 5 Nm off, and you will not feel it.

You change your wheels twice a year. The wheel bolts are the only thing holding the car to the road. A torque wrench is the tool that tells you when to stop, but how accurate is the clicking one from the discount aisle? Auto Bild took ten of them to a certified calibration lab and measured. The result is clear, and not all expensive wrenches win.

How Auto Bild tested

All ten wrenches were bought in shops. The test took place in the DAkkS-accredited calibration lab of the tool maker Gedore in Remscheid. Each wrench sat for an hour to acclimatise, then went on an automatic test bench according to DIN EN ISO 6789.

First three releases at the highest value. Then five releases each at the lowest value, at 60 percent and at the maximum, so 15 measurement points per wrench. From these the testers worked out the mean deviation, the spread and how many readings fell outside plus or minus 4 percent. Precision is more than half of the total grade. Handling, ratchet, scale readability, manual and calibration certificate make up the rest.

One more detail. The author tried to release some wrenches by hand on a lab device. Set to 40 Nm, he got 32 Nm once and over 50 Nm the next time. Human hands are not a test method. Source: AUTO BILD, 1 August 2026.

Winners and top picks

  • Hazet 5122-3CT: grade 1.4, very good, €129.03. Mean deviation only 0.93 percent at 120 Nm and 0.57 percent at 200 Nm, largest deviation 2.50 percent at the lowest scale value. The only wrench in the test that does not need to be released after use. Minus: the manual is pictures on the packaging.
  • Gedore TORCOFIX TF-K200 (40 to 200 Nm): grade 1.4, very good, €151.95. Handling grade 1.0, fine ratchet, right and left tightening, calibration certificate included. Largest mean deviation 2.67 percent (5.43 Nm) at 200 Nm, under 2 percent in the other two ranges.
  • Stahlwille 750NR/200: grade 1.6, good, €159.98. All three measuring points inside plus or minus 4 percent, only -0.78 percent at 120 Nm. Minus: low-contrast scale and 566 mm length.
  • Gedore Red R68900200: grade 2.1, good, listed at €116.41 (the text says under €100 in April). Made in Remscheid, very well built. At 200 Nm all five readings were at least 4 percent over, once 5.2 percent. After a readjustment in the lab it was more repeatable than every other wrench in the test, but that second run did not count in the grade.

Who should skip what

The Wera Click-Torque C 3 (2.0, €167.77) has good precision but a very stiff release and no calibration certificate. The KS Tools ERGOTORQUEprecision (2.5, €73.93) handles well but is only satisfactory on precision. The Proxxon MicroClick MC 200 (2.7, €84.95) clicks too quietly. The BGS 7183 (3.7, €67.04) has a great case and poor precision. The TECPO set (3.9, €24.29) is hard to adjust, only sufficient on precision and has no serial number.

Mistakes to avoid

  • Using it as a breaker bar. A torque wrench only tightens. Loosen with a normal bar.
  • Storing it tight. Most click wrenches should be set back to the lowest value. The Hazet is the exception in this test.
  • Trusting your feel. The lab test shows even an expert is off by 20 percent by hand.
  • Skipping the check after the wheel change. Re-tighten after about 50 km, we explained how in a separate article.
  • Forgetting calibration. A wrench that gets dropped or is used for years should be checked.

Do the math: Wheel change twice a year, 10 years: 20 tightening sessions. The Hazet at €129.03 costs about €6.45 per change. The TECPO set at €24.29 is €104.74 cheaper but only reaches 3.9. Look at what DIN 6789-2 allows: 4 percent. At 120 Nm that is up to 4.8 Nm of error. A wrench that sits 0.9 percent off, like the Hazet at 120 Nm, is off by about 1.1 Nm. Tool cost against a loose wheel: I know which one I pick.

FAQ

Which torque for my wheel? The value in your car manual. Do not guess, it differs between models and bolts.

Do I need 1/2 inch drive? Auto Bild tested 1/2 inch wrenches with a 40 to 200 Nm range. That is the usual size for wheel bolts.

Is the cheap Gedore Red enough? For a home garage, yes. Just know that at the top of its range it ran 4 percent or more over in the test, so have it checked and adjusted once in a calibration lab.

Ivan’s Take

I would buy the Hazet or, if I want the certificate and the right and left drive, the Gedore. If the budget is tight, the Gedore Red is a sensible compromise. I would not buy the €24 set to tighten the only thing that holds my wheels on.

Sources: AUTO BILD.

Published:

More from this section

The AvtoGear weekly

Once a week: new tests, the best deals and one useful tip for your car. Nothing extra.